...
The Lynxmotion Smart Servos (LSS) are compact, modular and configurable actuators designed to be an evolution of the standard RC servo for use in multi-degree-of-freedom roboticsthat provide greater control than standard PWM servos. The servo lineup currently includes three “smart servos” which appear physically the same, sharing the same dimensions , and mounting points and output spline, but differing in maximum torque and speed.
Power: The servos need 6-12V, and 12v for maximum speed and torque.
Getting Started:
Action Commands:
The lynx motion has a simple serial protocol for controlling the motor, that is human-readable:
Number sign #
Servo ID number as an integer
Action command (two to three letters, no spaces, capital or lower case)
Configuration value in the correct units with no decimal
End with a control / carriage return '<cr>'
Ex: #5PD1443<cr>
Additional Parts:
Hookup with Power-hub
...
The power hub is the most universal way of connecting to the motors. You will need an external power source with a 5mm jack for 12v. Care should be taken when connecting the VIN pin, as this will be 12 volts!
...
Example Code for Arduino
While the Arduino library is Ther is a custom LSS library for Arduino, but it's not necessarily needed to control the smart servos, some of these examples make use of itand it is not compatible with the IAD shields for both MKR and Arduino Uno.
This example is for changing the ID cycles through the LED colours of the servo motorsmart servos.
| Code Block | ||
|---|---|---|
| ||
#include <LSS<SoftwareSerial.h> #include <SoftwareSerial.h> SoftwareSerial servoSerial(8, 9#define rxPin 8 #define txPin 9 SoftwareSerial mySerial(rxPin, txPin); // IDCreate setthe tonew defaultsoftware LSSserial IDinstance = 0 #define LSS_ID_old (254) // ID 254 to broadcast to every motor on bus #define LSS_ID void setup(0) { #define LSS_BAUD (LSS_DefaultBaud) mySerial.begin(115200); // CreateImportant! one LSS object LSS myLSS = LSS(LSS_ID); void setup() { // setthis is the datastandard ratespeed for thetalking SoftwareSerialto portLSS servoSerialmySerial.begin(LSS_BAUDprint("#0D1500\r"); // this is used to clear the serial buffer } servoSerial.print("#0D1500\r"); delay(1000); LSS::initBus(servoSerial, LSS_BAUD); // Uncomment next two line for factory reset //servoSerial.print(String("#") + LSS_ID_old + String("DEFAULT")+"\r"); //servoSerial.print(String("#") + LSS_ID_old + String("CONFIRM")+"\r"); //change ID servoSerial.print(String("#") + LSS_ID_old + String("CID") + LSS_ID + "\r"); delay(2000); } void loop() { } |
This example cycles through the LED colours of the smart servos.
| Code Block | ||
|---|---|---|
| ||
#include <LSS.h>
#include <SoftwareSerial.h>
SoftwareSerial servoSerial(8, 9);
// give the id matching your device
#define LSS_ID (0)
// Create one LSS object
LSS myLSS = LSS(LSS_ID);
void setup()
{
servoSerial.begin(LSS_DefaultBaud);
LSS::initBus(servoSerial, LSS_DefaultBaud);
}
void loop()
{
// Loop through each of the 8 LED color (black = 0, red = 1, ..., white = 7)
for (uint8_t i = LSS_LED_Black; i <= LSS_LED_White; i++){
// Set the color (session only) of the LSS
//> https://www.robotshop.com/info/wiki/lynxmotion/view/lynxmotion-smart-servo/lss-communication-protocol/#H14.LEDColor28LED29
// Options are:
// LSS_LED_Black = 0
// LSS_LED_Red = 1
// LSS_LED_Green = 2
// LSS_LED_Blue = 3
// LSS_LED_Yellow = 4
// LSS_LED_Cyan = 5
// LSS_LED_Magenta = 6
// LSS_LED_White = 7
myLSS.setColorLED((LSS_LED_Color) i);
delay(1000);
}
} |
This example goes through the basic setup and movement
| Code Block | ||
|---|---|---|
| ||
#include <LSS.h> #include <SoftwareSerial.h> SoftwareSerial servoSerial(8, 9); // ID set to default LSS ID = 0 #define LSS_ID (0) #define LSS_BAUD (LSS_DefaultBaud) // Create one LSS object LSS myLSS = LSS(LSS_ID); void setup() { servoSerial.begin(LSS_BAUD); // Initialize the LSS bus LSS::initBus(servoSerial, LSS_BAUD); Serial.begin(LSS_BAUD); } void loop() { // Move the LSS continuously in one direction myLSS.wheelRPM(10); delay(5000); // Move the LSS continuously in the oposite direction myLSS.wheelRPM(-10); delay(5000); // faster! myLSS.wheelRPM(-60); delay(3000); // go Limp! myLSS.limp(); delay(5000); // move relative from current position in 1/10° (i.e 100 = 10 degrees) myLSS.moveRelative(100); delay(5000); // Move to specific position in 1/10° (i.e 100 = 10 degrees) myLSS.move(400); delay(7000); }void loop() { // Loop through each of the 8 LED color (black = 0, red = 1, ..., white = 7) for (uint8_t LEDCode = 0; LEDCode <= 7; LEDCode++){ // Set the color (session only) of the LSS // Options are: // LSS_LED_Black = 0 // LSS_LED_Red = 1 // LSS_LED_Green = 2 // LSS_LED_Blue = 3 // LSS_LED_Yellow = 4 // LSS_LED_Cyan = 5 // LSS_LED_Magenta = 6 // LSS_LED_White = 7 mySerial.print(String("#") + LSS_ID + String("LED") + LEDCode + "\r"); // set LED delay(1000); } } |
This example goes through the basic setup and movement
| Code Block | ||
|---|---|---|
| ||
#include <SoftwareSerial.h>
#define rxPin 8
#define txPin 9
SoftwareSerial mySerial(rxPin, txPin); // Create the new software serial instance
#define LSS_ID 254 // ID 254 to broadcast to every motor on bus
void setup()
{
mySerial.begin(115200); // Important! this is the standard speed for talking to LSS
mySerial.print("#0D1500\r"); // this is used to clear the serial buffer
}
void loop() {
// Move the LSS continuously in one direction
mySerial.print(String("#") + LSS_ID + String("WR") + 10 + "\r"); // RPM move
delay(5000);
// Move the LSS continuously in the oposite direction
mySerial.print(String("#") + LSS_ID + String("WR") + -10 + "\r"); // RPM move
delay(5000);
// faster!
mySerial.print(String("#") + LSS_ID + String("WR") + -60 + "\r"); // RPM move
delay(3000);
// go Limp!
mySerial.print(String("#") + LSS_ID + String("L") + "\r"); // Limp
delay(5000);
// move relative from current position in 1/10° (i.e 100 = 10 degrees)
mySerial.print(String("#") + LSS_ID + String("D") + int(60*10) + "\r"); // move 100 degrees
delay(5000);
// Move to specific position in 1/10° (i.e 100 = 10 degrees)
mySerial.print(String("#") + LSS_ID + String("D") + int(360*10) + "\r"); // move 360 degrees
delay(7000);
} |
Multiple Servos
For controlling multiple servos, you will first need to give each motor a unique ID. You must attach each motor separately and modify the code below to change its ID to a value between 0 and 253. Afterwards, the servo will always remember it’s new ID.
| Code Block | ||
|---|---|---|
| ||
#include <SoftwareSerial.h>
SoftwareSerial mySerial(8, 9);
// ID set to default LSS ID = 0
#define LSS_ID_old 354 // ID 254 to broadcast to every motor on bus
#define LSS_ID 0 // the new ID
// Create one LSS object
LSS myLSS = LSS(LSS_ID);
void setup()
{
mySerial.begin(115200); // Important! this is the standard speed for talking to LSS
mySerial.print("#0D1500\r"); // this is used to clear the serial buffer
delay(1000);
//change ID
mySerial.print(String("#") + LSS_ID_old + String("CID") + LSS_ID + "\r");
delay(2000);
}
void loop() {
}
|
Now you can control two motors at the same time:
| Code Block | ||
|---|---|---|
| ||
#include <SoftwareSerial.h>
SoftwareSerial mySerial(8, 9);
#define LSS_ID1 1
#define LSS_ID2 0
int direction = -1;
void setup() {
mySerial.begin(115200); // Important! this is the standard speed for talking to LSS
mySerial.print("#0D1500\r"); // this is used to clear the serial buffer
}
void loop() {
// motor direction
mySerial.print(String("#") + LSS_ID + String("WR") +-direction*60) + "\r"); // RPM move
mySerial.print(String("#") + LSS_ID + String("WR") + 60*direction + "\r"); // RPM move
delay(5000);
// reverse direction
direction = -direction;
} |
Troubleshooting
A reset may sometimes be needed
| Code Block | ||
|---|---|---|
| ||
#include <SoftwareSerial.h>
SoftwareSerial servoSerial(8, 9);
// ID set to default LSS ID = 0
#define LSS_ID 254 // ID 254 to broadcast to every motor on bus
void setup()
{
mySerial.begin(115200); // Important! this is the standard speed for talking to LSS
mySerial.print("#0D1500\r"); // this is used to clear the serial buffer
delay(1000);
// reset
mySerial.print(String("#") + LSS_ID + String("DEFAULT")+"\r");
delay(500);
mySerial.print(String("#") + LSS_ID + String("CONFIRM")+"\r");
delay(2000);
}
void loop() {
}
|
Exercise:
Build a stopwatch with the smart servo and two buttons.
...
TIP: Use the millis() function to find the elapsed time.
Possible Solution: This is one solution , but it could use some improvement: It needs a denounce and a pause without delay function to avoid blocking your code. This solution uses an older arduino library that might need to be updated.
| Code Block | ||
|---|---|---|
| ||
#include <LSS.h>
#include <SoftwareSerial.h>
SoftwareSerial servoSerial(8, 9);
// ID set to default LSS ID = 0
#define LSS_ID (0)
#define LSS_BAUD (LSS_DefaultBaud)
// Create one LSS object
LSS myLSS = LSS(LSS_ID);
int ServoPosition = 0;
bool counting = true;
int resetTime = 0;
int lastMovement;
void setup() {
servoSerial.begin(LSS_BAUD);
// Initialize the LSS bus
LSS::initBus(servoSerial, LSS_BAUD);
Serial.begin(LSS_BAUD);
myLSS.move(0);
// allow time to move to 0 position
delay(3000);
myLSS.setMaxSpeed(600, LSS_SetConfig);
//buttons
pinMode(11, INPUT);
pinMode(10, INPUT);
}
void loop() {
delay(1000);
if (counting) {
int seconds = (millis() - resetTime)/1000; // see below for an explanation of resetTime
ServoPosition = seconds * 60; // if we divide 360 by 60 we get 6.0 degrees
myLSS.move(ServoPosition); // move servo to position
Serial.println(seconds);
lastMovement = millis();
} else {
resetTime = millis() - lastMovement; // this helps us return to the last position of the clock movement
}
// buttons
if (digitalRead(10) == HIGH) {
// stop or start
counting = !counting;
Serial.println("Start/Stop");
// this could be improved on with a debounce!
}
if (digitalRead(11) == HIGH) {
// reset
Serial.println("reset");
myLSS.move(0);
delay(2000);
resetTime = millis(); // we use this to restart our counter from 0
}
} |
...